Dewalt Framing Nail Gun

DeWalt M-16 Nail Gun by David Wiggins « Grind365


Dewalt Framing Nail Gun News:

YouTube

A review of the Dewalt nail gun. Very nice nailer. See the full review at http://professional-power-tool-guide….

Original Source: http://www.youtube.com/watch?v=T1VMc9_9pq4

DEWALT D51844 Round Head 2-Inch to 3-1/2-Inch Framing Nailer …

Backed by 900 in./lbs. of driving power, the DeWalt D51844 Framing Nailer is ready to sink 2-inch to 3-1/2-inch long round head nails deep into even the toughest …

Original Source: http://www.amazon.com/DEWALT-D51844-2-Inch-Framing-Nailer/dp/B00009YUI4

DeWALT Nail Gun – Compare Prices, Reviews and Buy at Nextag

DeWALT Nail Gun – 45 results like Factory Reconditioned Dewalt D51238KR 18 Gauge 2 in. Brad Nailer Kit, Factory Reconditioned Dewalt D51321R 15 Degree 3/4 in. – 1-3/4 …

Original Source: http://www.nextag.com/dewalt-nail-gun/stores-html

YouTube

A review of the Dewalt nail gun. Very nice nailer. See the full review at http://professional-power-tool-guide….

Original Source: http://www.youtube.com/watch?v=T1VMc9_9pq4

DEWALT D51844 Round Head 2-Inch to 3-1/2-Inch Framing Nailer …

Backed by 900 in./lbs. of driving power, the DeWalt D51844 Framing Nailer is ready to sink 2-inch to 3-1/2-inch long round head nails deep into even the toughest …

Original Source: http://www.amazon.com/DEWALT-D51844-2-Inch-Framing-Nailer/dp/B00009YUI4


DeWalt DCN690M2 XR 18 Volt Cordless Framing Nailer

Click Here To Buy It Now! http://www.toolbritannia.co.uk/cordless-tools-b/nail-guns-b11/dewalt-dcn690m2–18v-li-ion-framing-nailer~dewtdcn690m2 For Great Pri…


alphapoet asked What’s the difference between a Brad Nailer and a Finishing Nailer?

I am learning how to work with wood and different projects call for these nailers and I’m not sure what the real difference is. I even saw a kit at Costcos with both and a Floor Nailer (I know what that one is for).

I need to do some moldings and I think I need a Frame nailer for that.

Any help is appreciated. If you can, include some practical usages for each type of nailer.

Thanks

And got the following answer:

while i thought some of the other answers were good or o.k., they might be just a little vague. i think that how you would use each of these tools would go further in answering your question. to start with, the brad nailer; i would use this to build a picture frame, or other small nailing project, requireing nails 1″ or less. with the finish nailer; if i were putting up window and door trim, chair rails, or floor trim, this would be the gun that you would use for that. a framing gun; if you are going to build walls, apply plywood, or exterior trim in certain applications, this would be the use for it. now as far as what type of tool to buy; if your use is for a hobby, then the less expensive combination kits should be fine for that. the same with the finish nailer, for just use on your own home project. just make sure that the nails for the guns are readily available for when you need more. you won’t want to have to run around or have to order them when you need them. now if you are planning to make your living with these tools; i would suggest that you check out a home improvement store, or tool supply house, for a better quality tool. then buy the best the best that you can afford so that you’ll be able to depend on it. this would be espessialy true with a framing gun. if this is the case for you, i would reccomend hitachi air tools, i use those for the tools that i need to depend on in my line of work. my finish nailer is a mid grade quality tool, and the brad nailer is basicly just for around my own house. as far as the compressor goes; once again buy the best that you can afford since it will be running all of your air tools and be used all of the time. here again, i bought a hitachi. i would advise you to avoid the dewalt compressor though, they seem to be having a lot of trouble lately, since they were bought out by black and decker. well i guess this turned into a pretty long answer, but i hope that it helps you out and good luck.

Gabriel asked Could I use a dewalt or porter cable or another brand nail gun on an ingersoll rand air compressor?

It can be any type of nail gun brad or framing or finish or another
P.s can also any other woodworking air tools be used on an ingersoll rand air compressor

And got the following answer:

If you wish, go ahead.

All Business asked Difference between the DeWalt D51844 and D51822?

I am looking into purchasing a nail gun and am confused on which I should get. I want to know why ones at 20 degrees and ones at 30 degrees. And why ones a full round and ones a clipped head? Is one used more often? Is it a preference? I am renovating a house and have found a need to invest in a framing gun. I have a few walls to frame and hope to use this to build a deck too?

And got the following answer:

Either gun would probably be fine for you. The D51822 (31deg) will get you into confined spaces a little easier. The D51844 (20deg) can use a thicker nail.

The difference in angle is just variation in preference from two different companies. DeWalt did not come up with these angles, they are copying older nail gun manufactures.

The difference between clipped head and round head are just different ideas (originally come up with by different companies) to stick the nails together to go into the gun. Clipped head nails are usually a little more expensive (clipping the head is an extra manufacturing process) but allow for a few more nails to be loaded at one time. Both types of nails, once they go into the wood, will work the same.

In summary, both guns will handle what you are doing. You are not going to look like a noob to all the contractors for having the wrong nail collation. Go into the hardware store and handle both guns. Try holding the gun in various positions like you were nailing something. Whichever feels best, buy it.

Oh, and put your deck together with bolts and screws. It would be a shame to have all that work come apart on you.